Redesain Tata Letak Pabrik Gula dalam Meningkatkan Efesiensi dan Produktivitas CV. Rizki Abadi

Pascal Sidqi Lubis, Hilda Ayu Retno Nur Fitria Dewi, Evi Selvi

Abstract


This study aims to improve the layout of CV Rizki Abadi's production facilities so as to increase efficiency and productivity. Redesign of the company needs to be done because consumer demand is often not met until it reaches 64.5 tons in 2020. This study only discusses material handling costs, productivity percentages, and the layout improvement model chosen by the factory owner from the three models proposed by the researcher. The layout analysis in this study uses the CRAFT algorithm. The CRAFT algorithm can provide the best layout improvement model output after exchanging the location of the facilities. The analysis shows that the total cost of material handling in the initial layout is Rp. 2,950,838. After repairs were made using the CRAFT algorithm and approved by the factory owner (model 3) by exchanging facilities between Work Station 3 (Draining) and Work Station 2 (Mold Stacking), material handling costs were more efficient to only Rp. 1,257,115.5 or 2 ,25%. Initial layout productivity also increased from 14.27% to 16.6%.


Keywords


Craft; Efficiency; Productivity; Layout Redesign

Full Text:

PDF

References


Agnes Novita Ningtyas, M. C. (t.thn.). Perancangan Ulang Tata Letak Fasilitas Produksi Dengan Metode Grafik Dan Craft Untuk Minimasi Ongkos Material Handling. Jurnal Rekayasa Dan Manajemen Sistem Industri, 3(3).

Athira Putri Naurasari, Y. S. (t.thn.). Analisis Usulan Perbaikan Tata Letak Fasilitas Station Converting (Studi Kasus : Pt Kencana Tiara Gemilang, Malang). Jurnal Rekayasa Dan Manajemen Sistem Industri, 4(7).

Charina, A. 2017. Optimalisasi Tata Letak Fasilitas Pabrik Pembuatan Bola Dengan Menerapkan Metode CRAFT. Universitas Brawijaya. Malang: Repository.ub.ac.id.

Erlian Supriyanto., S. 2011. Evaluasi Tata Letak Fasilitas di Pt “XYZ” Bandung. 1(2).

Hesti Maheswari, A. D. 2015. Evaluasi Tata Letak Fasilitas Produksi Untuk Meningkatkan Efisiensi Kerja Pada PT. Nusa Multilaksana. Jurnal Ilmiah Manajemen dan Bisnis, 1(3).

M.Y.S. Andika Putra, K. H. 2016. Analisis Tata Letak Pabrik Untuk Meningkatkan Efisiensi Perusahaan: Studi Pada PT Mataram Tunggal Garment. Tesis.

Pratiwi, M. N. 2018. Analisis Perencanaan Tata Letak Fasilitas Layanan Menggunakan Metode Craft (Studi Kasus Pada Pt. Taspen Kantor Cabang Utama Bandung). Bandung.

Ridwan, A. 2010. Analisis Pengaruh Tata Letak Mesin-Mesin Produksi Terhadap Produktivitas Karyawan Pada PT. Nusira Crumb Rubber Medan. Medan: Universitas Sumatera Utara.

Supriyadi, D. S. 2019. Perancangan Ulang Tata Letak Pabrik Menggunakan Metode Algoritma Computerized Relative Allocation Of Facilities Techniques(CRAFT). Jurnal INTECH Teknik Industri, 5(2).

Vivek Deshpande, N. D. 2016. Plant Layout Optimization using CRAFT and ALDEP Methodology. Productivity Journal by National Productivity Council, 57(1).

Yohanes, A. 2011. Perencanaan Ulang Tata Letak Fasilitas Di Lantai Produksi Produk Teh Hijau Dengan Metode From To Chart Untuk Meminimumkan Material Handling di PT. Rumpun Sari Medini. Dinamika Teknik, 5(1), 59 - 71.




DOI: http://dx.doi.org/10.33087/jmas.v7i1.342

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

J-MAS (Jurnal Manajemen dan Sains) Published by Master of Management Program, Faculty of Economics, Batanghari University
Adress: Fakultas Ekonomi, Jl.Slamet Ryadi, Broni-Jambi, Kec.Telanaipura, Kodepos: 36122, email: jmas.unbari@gmail.com


Creative Commons License This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.